Overview
A no-dig PE landscape edging kit is a surface-mounted border system designed to separate lawns from flower beds, mulch beds, tree rings, and planted garden areas without cutting a continuous trench. The flexible L-shaped UV-stabilized polyethylene coil follows straight or curved bed lines and is secured through pre-punched anchor tabs with 15 cm spiral stakes. Firm ground preparation, suitable stake selection at the 10 cm-centered anchor holes, and correct placement at curves and joins all influence how well the border stays aligned over time. EcoYardSupply supplies the kit factory-direct for garden centers, landscape distributors, contractors, and OEM private-label programs.
| Material | Polyethylene (PE), UV-stabilized |
|---|---|
| Length | 20 ft / 40 ft / 100 ft |
| Height | 4 in (10 cm) / 5 in (12.7 cm) |
| Stakes & anchor holes | 15 cm spiral stakes; pre-punched anchor holes at 10 cm centers. Not every hole requires a stake — installers select stake positions according to curves, joins, soil condition, and movement risk. |
| Included stake quantity | 8 stakes per 20 ft kit, 12 stakes per 40 ft kit, and 40 stakes per 100 ft kit. Additional stakes may be required for tighter curves, joins, loose soil, slopes, or locations exposed to repeated ground movement. |
| Install method | Installed on the soil surface with spiral stakes, without trenching |
| Colors | Brown, green, light gray, dark gray |
Kit contents: PE edging coil and spiral stakes
EcoYardSupply supplies this PE no-dig landscape edging kit factory-direct to importers, garden-center chains, landscape wholesalers, and OEM private-label brands. Standard stock MOQ is 100 kits per SKU combination (length × height × color). Full OEM programs — custom color assortments, bilingual retail packaging, stake counts, and master-carton branding — typically start at 500 kits per production run.
Stock orders usually ship within 15 days to 25 days after deposit confirmation, depending on coil length mix and destination port. OEM lead time commonly runs 30 days to 45 days once artwork, color chips, and packaging proofs are approved. Samples are available on request for fixture evaluation before bulk commitment.
Include kit length (20 ft, 40 ft, or 100 ft), profile height (4 in or 5 in), color, forecast quantity, and destination port when emailing sales@ecoyardsupply.com. Mixed-container export with raised beds or pruning tools is supported where approved.
Professional buyers often compare flexible PE no-dig kits versus rigid metal border profiles when building seasonal assortments. PE coils curve easily around tree rings and organic bed shapes, install without trenching, and ship lighter for e-commerce and big-box freight programs. Metal edging may suit formal straight runs where maximum rigidity and a premium visual line are prioritized over coil flexibility.
Material choice should also reflect the end user’s maintenance expectations. Flexible PE is easier to shape around curved flower beds and is lighter to handle, while rigid metal may be preferred for highly formal straight lines or locations where greater profile rigidity is required. Neither material replaces correct soil preparation, anchoring, drainage planning, or seasonal inspection.
| Factor | PE no-dig kit | Metal border profile |
|---|---|---|
| Install method | Surface mount with spiral stakes — no trench | Often requires trenching or hammer-in stakes |
| Curves & tree rings | Flexible coil follows gradual curves and tree-ring layouts; tighter curves require closer fixing points | Pre-bent sections or more cuts and joins |
| Freight & handling | Lighter coils — lower case weight for mixed loads | Heavier per linear foot — higher freight per unit |
| Retail positioning | DIY-friendly, contractor speed installs | Premium rigid border for formal landscapes |
| Typical wholesale MOQ | 100 kits stock / 500 kits OEM | Varies by profile — confirm at RFQ |
| Aggressive grass control | Helps define the surface boundary and reduce shallow runners; not a deep rhizome barrier | Effectiveness depends on profile depth and installation; shallow profiles may still be bypassed by rhizomes |
| Curved flower beds | Flexible coil can follow gradual curves; tighter curves require closer stake spacing | May require pre-bending, shorter sections, or additional joins depending on the profile |
For deeper selection criteria, read our plastic versus metal landscape edging guide and the wholesale landscape edging buying guide.
Stock programs support faster reorders, predictable stake counts (8 stakes per 20 ft kit, 12 stakes per 40 ft kit, 40 stakes per 100 ft kit), and mixed-color containers for distributors building fixture logic quickly. OEM customization adds private-label cartons, regional color assortments, multilingual instruction sheets, and retailer-specific case packs for chains that own shelf presentation.
Contractors evaluating freeze-thaw zones should plan closer stake spacing on curves and budget extra stakes for loose soil — the same kit performs differently by climate, drainage, and install discipline. Seasonal inspection and reset after ground movement is normal maintenance for any surface-mounted edging category.
Follow these steps for consistent crew results on residential and commercial borders:
Soil suitability: The supplied stakes are intended for workable garden soil. If the ground is extremely hard, heavily compacted, frozen, or filled with stones, do not continue hammering with excessive force. Loosen or prepare the fixing point first, or select an edging and anchoring system designed for hard-ground installation.
Important: This surface-mounted edging is intended to define and organize lawn-to-bed boundaries. It can help reduce shallow grass runners, but it is not a deep underground rhizome barrier. Aggressive grasses such as Bermuda grass may still travel beneath or around shallow edging and may require ongoing removal or a deeper root-control system.
Install steps: place, stake, join, trim
Q: How many stakes are included with each kit length?
A: 20 ft kits include 8 stakes. 40 ft kits include 12 stakes. 100 ft kits include 40 stakes.
Q: How do you cut the edging?
A: Cut the PE coil with garden shears or a utility knife.
Q: Can no-dig landscape edging lift or shift due to frost heave or ground movement?
A: Yes. Like most landscape edging systems, no-dig edging can move over time as soil expands, contracts, freezes, thaws, or becomes saturated. Proper anchoring helps reduce this movement. This edging uses 15 cm spiral stakes installed through pre-punched anchor tabs. In loose soil, tight curves, or areas with repeated freeze-thaw cycles, closer stake spacing or additional stakes may improve stability. Local soil, drainage, climate, and installation conditions should always be considered.
Q: How can I help prevent no-dig landscape edging from lifting out of the ground?
A: Install the edging on reasonably firm soil and drive the 15 cm spiral stakes fully through the anchor tabs with a rubber mallet. Use closer fixing points around curves and consider additional stakes where soil is loose or frequently disturbed. Good drainage can also help limit excessive soil movement. In regions with strong freeze-thaw cycles, inspect the edging seasonally and reset or reinforce sections if ground movement occurs.
Q: Will no-dig landscape edging stop Bermuda grass from entering a flower bed?
A: It can help define the lawn edge and reduce some shallow surface runners, but it should not be treated as a complete Bermuda grass barrier. Bermuda grass spreads through stolons and underground rhizomes that may travel beneath or around shallow surface-mounted edging. Regular inspection and removal are still required, and severe infestations may need a deeper root barrier or a broader grass-control plan.
Q: Can the edging be used around curved flower beds and tree rings?
A: Yes. The flexible PE coil can follow gradual curves and circular bed lines. Allow the coil to relax before shaping it, avoid forcing abrupt bends, and use closer stake spacing around tighter curves. For tree rings, check for visible surface roots and underground services before driving stakes.
Q: Can I mow or use a string trimmer next to the edging?
A: The edging can be installed along a mowable lawn-to-bed boundary, but the exposed PE profile should not be repeatedly struck by mower blades, mower decks, or string-trimmer line. Set a consistent visible height, keep the lawn side clear, and trim carefully to reduce cosmetic damage, cuts, or displacement.
Q: Will the edging keep mulch inside the flower bed?
A: It helps create a defined barrier that can reduce normal mulch migration into the lawn. Performance depends on the exposed profile height, mulch depth, slope, rainfall, drainage, and foot traffic. It is not designed to function as a retaining wall or to contain deep material on a steep slope.
Q: Is no-dig edging suitable for sloped beds or areas with heavy rain?
A: It may be used on gentle slopes when the soil is firm, drainage is adequate, and additional stakes are installed where movement is likely. However, edging alone cannot correct concentrated runoff, erosion, standing water, or significant grade differences. Drainage and erosion problems should be addressed before installation.
Q: How can I keep flexible plastic edging from looking wavy?
A: Prepare a smooth border line, allow the coil to relax before installation, form gradual curves, and anchor the tabs at consistent intervals. Add stakes near joins, direction changes, and any section that does not sit flat. For long formal straight runs where maximum rigidity is the main requirement, a rigid metal profile may be a more suitable choice.
Q: How can I prevent two edging sections from separating at the join?
A: Align or overlap the ends according to the kit configuration and place stakes close to both sides of the join. Do not leave an unsupported connection between widely spaced stakes. Recheck joins after initial soil settlement and after seasonal ground movement.
Q: Do I need to install a stake in every 10 cm anchor hole?
A: No. The pre-punched holes are positioned at 10 cm centers to give installers flexibility when selecting fixing points. A stake is not required in every hole. Use the supplied stakes at appropriate intervals for ordinary straight sections, and select closer fixing points around curves, joins, loose soil, gentle slopes, and areas where ground movement is more likely. Additional stakes may be required when the included quantity is not sufficient for the site conditions.
Q: What tool should I use to install the stakes, and are they suitable for hard soil?
A: Use a rubber mallet to drive the 15 cm spiral stakes into workable garden soil. The supplied stake material is not intended to be forced directly into extremely hard, heavily compacted, frozen, or rocky ground. If strong resistance is encountered, stop hammering and prepare or loosen the fixing point first. For consistently hard ground, choose an anchoring system designed for that soil condition.
Q: What is the MOQ?
A: Standard MOQ is 100 kits. OEM or custom orders usually start at 500 kits.
Q: Are samples available?
A: Yes. Samples are available on request.
Q: What is the lead time?
A: Stock orders usually ship within 15 days to 25 days after deposit confirmation. OEM programs commonly require 30 days to 45 days depending on quantity and customization.
For wholesale inquiries, please email sales@ecoyardsupply.com with kit length, color, quantity, and destination.
